TwitterpinterestFacebookInstagram



DO



The author of this page will appreciate comments, corrections and imagery related to the subject. Please contact Anatoly Zak.

 

Propulsion Module of the PTK spacecraft

Russia's PTK/Federatsiya new-generation transport spacecraft will consists of two main sections: the reentry module, VA, and the Propulsion Module, DO.

Previous chapter: Return Vehicle of the PTK spacecraft


 

cutaway

The propulsion module of the PTK Federatsiya (later Orel) spacecraft as of 2016.

From the publisher: Pace of our development depends primarily on the level of support from our readers! Please support this project:
Donate

Design of the Propulsion Module

The expendable propulsion module, known in Russian as Dvigatelny Otsek or DO, of the PTK spacecraft was designed to accommodate the ship's propulsion system, including a dual main engine and eight clusters of attitude control and orientation engines, DPOs, distributed around the module. Four clusters will be located in the front of the module, including a pair containing six engines each, and another two groups with five engines. Four more pairs of engines will be located on the aft bulkhead of the module.

The main propulsion system, KDU, is expected to include a dual s5.92 engine with a trust of two tons each developed at KB Khimmash design bureau in Korolev. The similar engine is used on the Fregat upper stage.

Propellant supplies in the low-pressure tanks of the PO module would be able to provide a total of around 1,300 meters per second in velocity change to the spacecraft, first of all for the departure from the lunar orbit toward Earth.

2013

The exterior design of the Propulsion Module, DO, circa 2013.


On its exterior, the DO module will carry a pair of deployable solar panels, the main communications antenna capable of maintaining link with ground control at lunar distances, the main rendezvous antenna of the Kurs-NA system, star trackers and other sensors of the flight control and navigation system.

Various avionics and power batteries will be located inside the DO module along with the tanks of the propulsion system. In July 2016, ZAO Orbita based in the city of Voronezh announced a contract with RKK Energia to develop equipment for power distribution and control aboard the PTK spacecraft, which had to be delivered in 2020.

A special detachable umbilical mast will connect key systems of the DO module and the Return Vehicle, VA, carrying the crew. During the launch and the ascent to orbit, the DO module will be protected by a payload fairing, which will split into several segments and fall away above the dense atmosphere.

The DO and VA modules will remain connected during the most of the flight separating only during the final reentry into the Earth's atmosphere at the end of the mission. The DO module will then burn up over a remote part of the ocean.

Development

do

Photo released in December 2020 shows a prototype of the Propulsion Module during manufacturing.


At the origin of the PTK program as a joint effort with the European Space Agency, Europe's aerospace industry was to be responsible for the propulsion module. Following the breakdown of the Russian-European cooperation on the project in 2009, the development of the module shifted back to Russia.

Seemingly lagging behind the work on the Return Vehicle, the DO module underwent several incarnations while still on the drawing board in the 2010s. One early configuration studied around 2013 featured torus-shaped tanks. However in an apparent effort to provide more propulsion capability and to save weight, a new complex geometry of the propellant tanks emerged by the mid-2010s. The latest architecture relied on tried and proven spherical tanks to store hypergolic propellant. A pair of three-tank clusters, including a pair for fuel and oxidizer and one smaller tank carrying pressurization gas, were tightly integrated inside the cylindrical compartment. In 2016, a similar design of the propellant tanks was also adopted for the new-generation cargo ship, TGK PG.

In another major design change, the DO module's flat aft bulkhead became bulbous to accommodate more propellant during lunar missions...

 

Next chapter: Design evolution of the DO module (INSIDER CONTENT)

 

Text and main illustration by Anatoly Zak; Last update: October 22, 2024

Page editor: Alain Chabot; Last edit: November 14, 2016

All rights reserved

 

insider content

 

DO

The propulsion module of the PTK NP spacecraft circa 2011. Click to enlarge. Credit: RKK Energia


Cutaway

PTK

Depictions of the PTK NP spacecraft released in June 2013 at the Le Bourget Air and Space Show. Note flat aft bulkhead. Credit: RKK Energia


do

do

A propulsion module of the PTK NP spacecraft as of 2013. Credit: RKK Energia


S5.92 engine

The S5.92 engine serves as the main propulsion unit of the Fregat upper stage. Click to enlarge. Copyright © 2008 Anatoly Zak


S5.92 engine

Deployment test of Orel's solar panel in 2024. Click to enlarge. Credit Roskosmos


 

to spacecraft home