to Space launchers main page to Proton main page RD-253

Twitter



RD-253 engine series for Proton's first stage

The original first stage of the Proton rocket was propelled by six RD-253 engines developed at OKB-456 design bureau (now NPO Energomash) in Moscow and led by Valentin Glushko. Each engine had a thrust on the ground of 150 tons. Like the engines on two upper stages of the Proton rocket, RD-253 burned highly toxic unsymmetrical dimethylhydrazine as a fuel mixed with nitrogen tetroxide as an oxidizer.

RD-253

A full-scale demo version of the RD-253 engine.


Specifications of RD-253 engine:

-
RD-253
RD-275
Thrust at sea level
150 tons
162 tons
Thrust in vacuum
166 tons
178 tons
Specific impulse on the ground
285 seconds
287 seconds
Specific impulse in vacuum
316 seconds
316 seconds
Dry mass of the engine
1,080 kilograms
1,080 kilograms
Fueled mass of the engine
1,260 kilograms
1,070 kilograms
Length of the engine
3,000 millimeters
3,050 millimeters
Diameter of the engine
1,500 millimeters
1,500 millimeters

On the first stage of the Proton rocket, RD-253 was installed in a movable suspension system that allowed to swivel each individual engine around a single axis. Combined movement of all six engines enabled the flight control system of the rocket to steer the vehicle along its prescribed trajectory.

In 1986, specifically for the launch of core module of the Mir space station, the thrust of RD-253 engine was increased by seven percent. It was achived thanks to a minor modification to the propellant flow control valves. Since then, engines incorporating this change have undergone extensive additional qualification firings, in order to approve them for use in standard production vehicles.

From 1987 to 1993, NPO Energomash developed a more powerful version of the engine, designated RD-275, which has been used on the first stage of the Proton rocket until 2007, when the improved RD-276 model was introduced. The engines were mass produced at PPO Motorostroitel (also known as Permskie Motory or PAO Proton-MP) in the city of Perm. During a visit to Perm of Roskosmos haed Dmitry Rogozin, a poster on wall of the Proton PM exhibit hall indicated that the production of the engines at the company was first set up in 1962, of three years before the first launch of the Proton rocket.

Production

An engine from the RD-253 series in production circa 2016.


As late as 2017, Proton's first stage engines still used non-Russian components, most likely produced in Ukraine, and NPO Energomash promised to certify Russian-built replacements in 2018.

In September 2018, Acting Director at PAO Proton PM Dmitry Shenyatsky, quoted by RIA Novosti, said that four final RD-276 engines would be produced and tested by the company in the first quarter of 2019. However, the final test was actually conducted on November 14, 2019, Roskosmos announced. According to the State Corporation, Proton PM manufactured more than 90 sets of the RD-276 variants and conducted around 770 firing tests. According to industry sources, by that time, 77 sets of engines flew on Protons and more than 13 sets still remained for future launches.

In total, the company had produced more than 3,000 engines for different variants of the rocket, Roskosmos said.

In the December 2019 issue of the company's newspaper, Proton PM confirmed that the production of the RD-276 engines had been finished and one engine in the final pair had been transferred to GKNPTs Khrunichev in November 2019. One more was apparently shipped in early 2020.

In April 2021, Head of NPO Energomash Igor Arbuzov said that the RD-276 production line in Perm had been mothballed in operational readiness, however, there had been no decision to resume their production at the time.

 

 

 

Page author: Anatoly Zak;

Last update: October 18, 2021

All rights reserved

 

assembly

production

RD-253 engines during assembly. Credit: Proton PM


Cutaway

The 11D43 engine proposed by Valentin Glushko around 1960 for the first stage of the Proton rocket. It had low-expansion ratio and could be gimbaled to control the rocket in flight. Four such engines along with four 8D43 engines would be used on the first stage, if this configuration was ever built. Click to enlarge. Copyright © 2000, 2011 Anatoly Zak


scale

A scale model of RD-253 engine. Copyright © 2001 Anatoly Zak


stage

A business end of the Proton rocket with six RD-275 engines arranged in circle on the first stage. Click to enlarge. Copyright © 2000 Anatoly Zak


stand

A test stand in the city of Perm used for live firings of RD-275 engines. Credit: Roskosmos


stage

RD-276 engines lift the Proton-M rocket with the Elektro-L3 satellite on December 24, 2019. Click to enlarge. Copyright © 2000 Anatoly Zak


 

to Rockets home to launchers home to Proton home